Poultice Stain Remover

Key Features

Effectively removes deep-set oil and grease stains
Safe, non acidic, abrasive cleaning powder
Excellent cleaning additive

For use on

All natural stone (such as granite, limestone, marble, slate, and travertine), porcelain, quarry, Saltillo, terra-cotta, cement pavers, masonry surfaces, and other porous tile and grout surfaces.

Description

Poultice Stain Remover is a dual purpose, non-acidic stain remover. It is an absorptive clay that is designed to remove deep-set oil and grease stains without scrubbing. It is also a fine abrasive cleaning powder that removes surface stains and grout haze. Very effective on all natural stone and tile surfaces.

Limitations

Do not allow product to come in contact with any non-recommended surface
Light abrasive action or high RPMs on the surface of some marbles may dull the high-polished finish

Application of Product

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.

FOR REMOVING DEEP-SET OIL AND GREASE STAINS: Read entire label before using. Mix Poultice Stain Remover powder with water to form a thick, pliable paste. Quantity of Poultice Stain Remover needed will depend on size of stain. Apply a 1/4″ (6 mm) thick layer of paste directly over stain with at least a 1″ (25 mm) overlap beyond edge of stain. Cover with plastic or wax paper. Poke a few very small holes in plastic cover to allow for minimum air exposure. Allow paste to stand on stain for 24 to 48 hours. Remove Poultice Stain Remover with plastic spatula or plastic putty knife and wash off residue with clean water. Repeat procedure if necessary. If area darkens from absorbed moisture, it should dry completely within 5 to 7 days. FOR REMOVING SURFACE STAINS AND GROUT RESIDUE: Read entire label before using. Protect surrounding areas from splattering to minimize cleanup. Pre-wet a manageable area of the surface with water, approximately 10 ft (1 M) and sprinkle Poultice Stain Remover onto the area mixing into a thin slurry. If surface is vertical, mix slurry in a container and apply to pre-wet surface. Agitate by hand or with low RPM (175-350 RPM) buffer using a white nylon scrub pad. Keep surface wet throughout buffing process. Remove Poultice Stain Remover solution with clean towels or sponge and rinse twice with clean water. A wet/dry vacuum may be used. Rinse with clean water and buff dry with clean towels NOTE: Poultice Stain Remover is an excellent additive that will boost the cleaning power of many of the Aqua Mix® cleaners such as Phosphoric Acid Substitute, Heavy-Duty Tile & Grout Cleaner, and Stone Deep Clean.

Product Data Sheets

Technical Data Sheets

Safety Data Sheets

Problem Solving Guides

Cleaning of equipment

Clean tools with water before material dries.

How to Guide:

Removal of Deep-Set Stains from Porous Tile/Natural Stone/Masonry Stain Removal Guide

VOC Content

No VOCs

Available in

340grams, 2.7Kgs

Product Warranty

Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase. CUSTOM’s sole liability under this warranty shall be limited to the replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with CUSTOM’s printed instructions. CUSTOM makes no other warranties either expressed or implied. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or from one country/territory to another. This warranty is not transferrable.

Require Technical Assistance?

Please contact us at 1300 AQUA MIX or info@aquamix.com.au