Enrich’N’Seal™

Key Features

Rejuvenates the colour and improves the appearance of worn and weathered stone
Maximum Stain Resistance
State-Of-The-Art Polycure™ Technology
May also be used as a pre-grouting sealer
Does not alter the slip resistance of sealed surface
Allows moisture-vapour transmission
Low VOC
Effectively seals and darkens the colour of grout joints
Lasts up to 15 years

For use on

Enrich’N’Seal is used as an enhancing sealer for all unsealed natural stone such as marble, granite, slate, limestone, travertine, quartzite. It also effectively seals and darkens the colour of grout joints. Effective for interior and exterior applications.

Description

Enrich’N’Seal™ is a premium, no-sheen, enhancing sealer for stone, 100% polymer-solid with State-Of-The-Art Polycure™ Technology. It is a penetrating sealer formulated to darken, enrich, and highlight the character and beauty of unsealed natural stone. May also be used as a pre-grouting sealer. Allows moisture vapor transmission. It also effectively seals and darkens the color of grout joints. Formulated to provide maximum stain protection. Lasts up to 15 years

Limitations

Do not allow sealer to come in contact with any non-recommended surface as product is not completely removable
Sealers and finishes should not be used with Enrich ‘N’ Seal
If Enrich’N’Seal is not wiped completely dry within 5 minutes, a residue may form. If residue occurs, contact Technical Services for additional options
Keep floor surfaces dry and clean to reduce possibility of slip-fall accidents. Routine pressure-washing will affect expected wear
Sealers will not prevent surface wear or etching from acids or caustic chemicals

Preparation

Surface should be dry, clean and free of waxes, sealers or finishes. New installations need to be dry 48 hours before application. Protect surrounding surfaces. Test product in an inconspicuous area to ensure desirable results. The Stone, Tile or Grout must be dry prior to applying sealer – the following document explains in detail the definition of the term “dry” as it relates to sealer application. READ MORE

Pre-Grout Sealer/Grout Release

Porous tile and stone can be stained by grout during installation. Sealing the tile before grouting will make grout removal much easier. Apply a single coat of sealer according to directions after tile has been bonded for a minimum of 24 hours, or apply to front face of tile before installation. Wait a minimum of 48 hours before grouting. IMPORTANT: Enhancing Sealers should NOT be applied over a previously sealed surface. This includes surfaces that have been pre sealed with Aqua Mix® ProBlockor any other pre sealer, and surfaces that have had Aqua Mix® Grout Release applied. Pre sealers and Grout Release products can cause Enhancing Sealers to enhancer the stone unevenly and become patchy in appearance.

Procedure

Apply using a sponge, brush, paint pad, cotton towel. NOTE: Avoid overlapping and rundown. On vertical surfaces, apply bottom to top or apply to each tile prior to installation.
Be sure any sealer that does not penetrate surface is wiped completely dry off surface within 5 minutes of each application using clean, dry, absorbent paper, cotton or microfiber towels. If sealer residue is not completely removed from stone and grout surface within 5 minutes of application, a residue may form.
If 2 or more applications are used, allow a minimum of 30 minutes drying time between applications. Some highly porous surfaces may require an additional application after full cure insuring that all residue is removed within 5 minutes.
Enhancing Sealers should not leave a gloss or sheen to the surface, ensure all surface has been buffed dry before leaving to dry.

Drying Time

Allow 30 minutes drying time between applications when conditions are 20° Celsius & 70% RH. If temperatures are lower or humidity higher then these times may be longer. If unsure about the specific job site temperatures and conditions please contact one of our technical advisors.
Ready for surface traffic in minimum of 2 hours.
Keep dry for a minimum of 12 hours.
Achieves a full cure in minimum of 48 hours.

Product Data Sheets

Technical Data Sheets

Safety Data Sheets

Problem Solving Guides

Cleaning of equipment

Clean tools with mineral spirits immediately after use.

VOC Content

Maximum VOCs: 210 grams per liter

Available in

473ml, 946ml, 3.8L.

How To Videos

Product Warranty

Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase. CUSTOM’s sole liability under this warranty shall be limited to the replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with CUSTOM’s printed instructions. CUSTOM makes no other warranties either expressed or implied. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or from one country/territory to another. This warranty is not transferrable.

Approx. Coverage m² per/L

	Polished	Honed	Textured
Marble	25-35m²	15-20m²	12-18m²
Limestone	20-25m²	8-12m²	6-10m²
Travertine	25-30m²	15-25m²	10-15m²
Granite	30-40m²	25-35m²	20-30m²
Bluestone / Basalt	25-35m²	20-30m²	15-25m²
Sandstone	15-20m²	10-15m²	6-10m²
Slate	20-30m²	15-20m²	10-15m²
Concrete	15-25m²	10-15m²	6-10m²
Terrazzo	20-25m²	15-20m²	10-15m²
Terracotta	N/A	N/A	8-15m²

Require Technical Assistance?

Please contact us at 1300 AQUA MIX or info@aquamix.com.au