Sealer’s Choice® Gold – Rapid Cure is a premiumgrade, high performance penetrating / impregnating stone, tile & grout sealer. It is a low VOC, water-based sealer formulated to provide maximum stain protection, especially in food preparation and serving areas. Ideal for all interior and exterior natural stone (including around salt water swimming pools), tile & grout surfaces. This premium sealer also includes built-in Microban® – Cured Sealant is Mould & Mildew Resistant, and this sealer lasts up to 15 years.
Key Features:
Maximum stain protection
May be used as a pre-grouting sealer
Allows moisture vapour transmission
The NEW Rapid Cure Formula protects in less than 4 hours
As a natural look sealer for all natural stone surfaces (such as sandstone, slate, quartz, marble, limestone, granite, bluestone / basalt) unglazed tiles, polished & unpolished porcelain tiles, clay pavers, polished & unpolished concrete, terrazzo, brick, grout, masonry, encaustic tiles, terracotta and grout. Suitable for both interior and exterior use.
Limitations:
Do not allow sealer to come in contact with any non-recommended surface.
If the product is allowed to dry on the surface, a white film may form. If this occurs, scrub with Aqua Mix® NanoScrub® and a white nylon pad.
The sealer will not prevent surface wear or etching from acids or caustic chemicals.
Surface Preparation
The surface should be dry, clean and free of waxes, sealers or finishes. New installations need to be dry 24 hours before application. Protect surrounding surfaces. Test product in an inconspicuous area to ensure desirable results. The Stone, Tile or Grout must be dry prior to applying sealer – the following document explains in detail the definition of the term “dry” as it relates to sealer application. READ MORE
Pre-Grout Sealer / Grout Release:
Porous tile and stone can be stained by grout during installation. Sealing the tile before grouting will make grout removal much easier. Apply sealer according to directions after the tile has been bonded for a minimum of 24 hours, or apply to the front face of tile before installation. Wait a minimum of 2 hours before grouting.
Procedure
Always test a small area first to ensure satisfactory results.
Apply using a pump sprayer, paint pad applicator, lambswool applicator, sponge or brush.
Allow it to penetrate for up to 5 minutes, if the surface is drying within 5 minutes, apply more sealer to keep surface wet for up to 5 minutes.
Wipe surface completely dry using clean, dry cotton, paper or microfiber towels after each application. Ensure no sealer is allowed to dry on the surface.
Porous surfaces may require additional applications.
Conduct a test to see if the surface is completely sealed after 2 hours by applying drops of water on the surface. If it penetrates, an additional application is required.
Drying Time
Allow 30 minutes of drying time between applications when conditions are 20° Celsius and 70% RH.
If temperatures are lower or humidity higher than these times may be longer.
If unsure about the specific job site temperatures and conditions please contact one of our technical advisors.
Ready for surface traffic in a minimum of 2 hours.
Regurlar cleaning should consist of a regular mop or light scrub with a pH neutral detergent, or Aqua Mix Concentrated Stone & Tile Cleaner at a dilution rate of 1 part product to 80 parts water. Using this product on a regular basis will safely remove soiling and help prevent a stubborn build up without damaging the tile, grout or sealer. This product is a pH Neutral formula and will not harm any other water-safe surfaces.
Then agitate the floor using either an Aqua Mix AquaScrub or rotary floor scrubbing machine.
Extract liquid off of the floor using either a microfiber mop or a wet vacuum cleaner fitted with a squeegee head.
Rinse thoroughly with clean potable water. Mop up rinse water off the floor.
Sealer Reapplication: Thoroughly clean the surface using the periodic cleaning method, then reapply sealer following application instructions as per label. No stripping will be required for reapplication. Please review specific sealer data sheets for recommended reapplication period.
Aqua Mix Sealers Notes: All spills should be wiped up immediately to reduce the chances of absorption. It is important that no acidic cleaners or products that contain solvents are used on sealed natural stone.
After cleaning with a pH neutral cleaner. Sealed (left side) Limestone Unsealed (right side)
Product Warranty
Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase. CUSTOM’s sole liability under this warranty shall be limited to the replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with CUSTOM’s printed instructions. CUSTOM makes no other warranties either expressed or implied. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or from one country/territory to another. This warranty is not transferrable.
Key Features:
Key Features:
Where to Buy
