A glossy, highly reflective surface
- Surface is very smooth and not very porous
- Polished crystals bring out brilliant colors and grains (400 to 3500 grit to polish stone)
- Shine comes from the natural reflection of the stone’s crystals
- Polish can wear away due to heavy foot traffic and improper maintenance
A slightly rough texture that is achieved by tumbling small pieces of marble, limestone or granite to achieve an old-world/worn appearance
A flat matte to low sheen gloss
- Surface is very smooth, but very porous
- Many more and wider gaps in surface than polished stone
- Medium density
- Commonly used in low traffic areas or for aesthetics
- Colors are not as vibrant as a polished stone
SAND BLASTED MARBLE
Pressurized flow of sand and water that results in a matte finish
Pounding action of hammer develops textured surface. Reduces stone’s color tones
Pre Sealing Marble
Occasionally pre sealing marble is required prior to installation, especially lighter colors as they can become translucent when wet. It is always best to consult with your stone supplier to verify whether your marble requires this treatment. If required, sealing marble on all six sides using Aqua Mix® ProBlock a minimum of 24 hours prior to installation.
Aqua Mix® ProBlock is a water based penetrating sealer designed to resist staining caused by water soluble minerals (including picture framing effect) which are normally absorbed through the back of the stone during installation. It also helps resist efflorescence migration.
If applying an Enhancing Sealer as the final surface seal, DO NOT apply any ProBlock to the top surface as it will stop the penetration of enhancing sealers. Please contact Aqua Mix® prior to installation if an enhancer is specified for use.
Pre-Grout Sealing Marble
If the stone does not require to be pre-sealed, it is generally recommended to apply a coat of sealer on the surface prior to grouting. This is to act as a grout release and assist in the grout clean-up process. This is very important as acidic cleaners cannot be used to removed cured grout residue.
If the surface is textured (sandblasted, bush-hammered, tumbled) applying a coat of Aqua Mix® Grout Release would work best.
If the surface is smooth (polished, honed) than applying a coat of the final sealer you select is recommended.
Grout Haze Removal
It is important that all of the grout haze is removed between 3-10 days. A minimum of 3 days for the grout to cure and harden, and no longer than 10 days or it may need to be mechanically removed.
Grout haze can be removed using Aqua Mix® NanoScrub®, if Aqua Mix® Grout Release was used, the grout and Grout Release can be removed using Aqua Mix® Heavy-Duty Tile & Grout Cleaner. If epoxy grout has been used you can remove using Aqua Mix® Sealer & Coating Remover.
Detailed instructions: Click here
Smooth surfaces (polished, honed) should only be sealed using either a Natural Look Sealer or an Enhancing Sealer. The best sealer for marble is Aqua Mix® Sealer’s Choice® Gold – Rapid Cure, however, we have a range of sealers to suit your requirements:
Sealing Marble with a Natural Look Penetrating Sealer:
- Good: Aqua Mix® Penetrating Sealer
- Better: Aqua Mix® Pro-Solv®
- Best: Aqua Mix® Sealer’s Choice® Gold – Rapid Cure or Aqua Mix® Ultra-Solv®
Sealing Marble with an Enhanced Look Penetrating Sealer:
Note: Sealing marble with a penetrating sealer will not alter the slip resistance. For more information regarding slip resistance, click here
Maintaining Marble Surfaces
Countertops and Walls
Countertops/Bench-tops, vanities, and walls should be regularly cleaned using any of Aqua Mix® Routine Cleaners.
Regular use of Aqua Mix® Aqua Shield™ Cleaner & Resealerwill ensure that your marble always maintains maximum stain resistance.
Floors should be regularly cleaned using Aqua Mix® Concentrated Stone & Tile Cleaner. If the surface is allowed to build up, then scrub the surface using Aqua Mix® Stone Deep Clean, Aqua Mix® Heavy-Duty Tile & Grout Cleaner or Aqua Mix® NanoScrub® and an Aqua MIx® AquaScrub.
Etching of Marble
Because carbonates (marble, travertine or limestone) react to acid (acidic liquids & cleaners) to create carbon dioxide, the effects to the stone are permanent. The destruction of carbonates shows on the surface of stone as etching.
Although the particles of stone cannot be recovered, they can be polished or refinished to match the finish of the stone.